| |
products  enamels
SR 235 The red enamel SR 235 is made with epoxy esters and high chemical resistance pigments. It is suitable when a finish with special chemical agents and friction protections, combined to a strong adhesivity to supports to paint is required. It is compatible with all types of enamelled wire. It features high dielectric resistance and a very good water and saline resistance. It can be also supplied in the colours green and black.
C H A R A C T E R I S T I C S
|
STANDARD |
VALUE |
| Colour |
- |
Brick red |
| Density a 25 °C |
ASTMD 115/72 |
1,150 - 1,250 |
| Viscosity 25 °C |
ASTMD 2393/80 |
900 - 1200 mPa.s |
| Dry residual 135 °C |
ISO 3251 |
58% - 61% |
| Drying to the touch |
ASTMD 115 |
30' - 40' |
| Corrosion on copper |
IEC 464 - 2.8 |
Absent |
| Dielectric strength |
IEC 464 - 2.16 |
6.100 V/0,1mm |
SR 260 The enamel SR 260 is made with modified epoxy resins specifically designed for anti-trace coverings.
It forms a film with special characteristics of hardness and of chemical agents and superficial discharge resistance, with values comparable to those ones of ceramics materials.
It is recommended for security and high quality coverings.
C H A R A C T E R I S T I C S
|
STANDARD |
VALUE |
| Colour |
- |
(A) red (B) ivory |
| Density at 25 °C (after mixing) |
ASTMD 115/72 |
1,230 - 1,190 |
| Dielectric strength |
IEC 464 - 2.16 |
2.600 V/0,1mm |
| Superficial endurance |
IEC 464 - 2.17 |
2X1010 W |
| Arc resistance |
IEC 464 - 2.18 |
"125" |
SR 269 The red enamel SR 269 is made with special resins desgned to obtain very good oil and chemical agents resistance.
It is suitable for finishes on coil band, on stators, for finish of cowls in mica and for protecting all type of electrical equipments.
It has a rapid essication and it is compatible with all types of enamelled wire.
It can be also supplied in the colour black and in tropicalized version.
C H A R A C T E R I S T I C S
|
STANDARD |
VALUE |
| Colour |
- |
Brick red |
| Density at 25 °C |
ASTMD 115/72 |
1,180 - 1,220 |
| Viscosity 25 °C |
ASTMD 2393/80 |
550- 570 mPa.s |
| Dry residual 135 °C |
ISO 3251 |
53% - 59% |
| Drying to the touch at 25 °C |
ASTMD 115 |
60' - 80' |
| Corrosion on copper |
IEC 464 - 2.8 |
Absent |
| Dielectric strength |
IEC 464 - 2.16 |
4.900 V/0,1mm |
The enamels here shortly described represent a minimum part of our production.
For further technical information and/or specific requests you can contact us to the following address:
angi@angisrl.com
Notes:
The information given in this data sheet are the results of careful researches and several tests carried out in our laboratory.
Because of the various and particular applications, these information are merely indicative without our responsibility.
| |
angi@angisrl.com
Administration office
20127 Milano
viale Brianza, 8
tel. +39 02.26144247
fax +39 02.2893746 | | Commercial offices and warehouse
14018 Villafranca d'Asti
loc. Case Bruciate, 37
tel. +39 0141.943825
fax +39 0141.943170 |
|
